CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 1 of 28 INSTALLATION AND MAINTENANCE MANUAL FOR CONAX BUFFALO PC PROGRAMMABL
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 10 of 28 6.2.6 Units. Next, verify or select the “Engineering Units”. If appropriate, o
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 11 of 28 digits that can be displayed before the decimal point depend on the display capabi
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 12 of 28 6.2.13 Next, TAB over to the I.D. Tag: and type in up to 8 alpha-numeric charact
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 13 of 28 Figure 10 – Example Input Feature Selection Screen 6.3.2.1 Set points. This s
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 14 of 28 6.3.4 You can enable another toolbar icon that can configure several indicators w
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 15 of 28 Table 1 – Example Printout Configuration and Calibration Information Device Stat
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 16 of 28 6.4 INPUT FILTERING Input filtering is of great importance in measurement appli
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 17 of 28 6.5 USER DEFINED TABLES For applications where the input is non-standard and non
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 18 of 28 Table 2 *User defined table for *IRt/c.xxx-K-80F/27C *Minimum range -70 degrees
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 19 of 28 Figure 11 6.5.3 Using the UDT. When configuring the sensor, select “User Def
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 2 of 28 TABLE OF CONTENTS SECTION DESCRIPTION PAGE 1.0 SCOPE 3 2.0
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 20 of 28 6.6 CALLENDAR-VAN-DUSEN APPLICATIONS The Callendar-Van-Dusen formula provides con
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 21 of 28 Please Note: The calculated values may be verified by using the device in simula
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 22 of 28 To enter the trimming screen, click “Device” then “Trimming” from the main screen’
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 23 of 28 8.0 SIMULATION FUNCTION The simulation function allows the user to check the re
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 24 of 28 Warning: The indicator is running in a special software mode while in simulation m
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 25 of 28 Appendix A Appendix A FIGURE A1 - SPM with Two SPDT Relay Option Wiring Diagram
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 26 of 28 Appendix A Figure A2 – SPM with two SPST Relay Option Wiring Diagram
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 27 of 28 Appendix A Figure A3 - SPM for AC Measurement Wiring Diagram
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 28 of 28 Appendix B APPENDIX B PROGRAMMING SOFTWARE MEDIA & MEDIA PO
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 3 of 28 1.0 SCOPE This manual provides instructions on setup and use of Conax Buffalo Tech
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 4 of 28 4.0 SPECIFICATIONS 4.1 SENSOR INPUT TYPES THERMOCOUPLE: Most standard types an
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 5 of 28 TEMPERATURE STABILITY: Better than 0.012%/˚C of span COLD JUNCTION COMPENSATION:
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 6 of 28 6.0 SOFTWARE INSTALLATION AND CONFIGURATION 6.1 SOFTWARE INSTALLATION CAUTION BE
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 7 of 28 Figure 1 – Setting the Communications Port Figure 2 – Connecting the PA-400 to
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 8 of 28 6.2 CONFIGURATION 6.2.1 Connect the PA-400 programming adapter into the proper se
CONAX BUFFALO TECHNOLOGIES TSD 43.021 Rev. ORIG Page 9 of 28 6.2.5 You can now view or modify any setting. Select the input sensor type by cli
Kommentare zu diesen Handbüchern